Key size and conversion table
| inches | millimeters | key |
|---|---|---|
| 0.591 | 15mm | |
| 0.600 | 5/16 Wworth 3 /8 BSF < /td> | |
| 0.625 | 5/8 AF | |
| 0.630 | 16mm | 16mm |
What is the equivalent of a 15mm wrench?
| SAE | Metric | Inch |
|---|---|---|
| 9/16 | 0.563 | |
| 15 mm | 0.591 | |
| 19/32 | 0.594 | |
| 5/8 | 0.625 |
What is the same size as a 15mm jack?
| MM | Approximate size in inches | Exact size in inches |
|---|---|---|
| 14 mm | 9/16 inch | 0.55118 inch |
| 15 mm | Just under 5 /8 inch | 0.59055 inch |
| 16 mm | 5/8 inch | 0.62992 inch |
| 17 mm | Just under 11/16 inch | 0.66929 inch |
Is 15mm equal to 3 4?
15mm = almost 19/32 inch. 16mm = 5/8 inch. … 19mm = 3/4 inch.
What metric and SAE sizes are the same?
Here’s a general rule for metric/SAE sockets that are identical (or close enough): 5/16″=8mm. 7/16″=11mm. 1/2″=13mm.
Why do key sets skip sizes?
Re: Why do key sets have missing sizes? ! It depends on which set you get. Sometimes they omit sizes that are not often used. That way they look good in the sales flyer because they span from 1/4 to 7/8, for example. But what they don’t tell you is that they don’t have all sizes.
What are the most common key sizes?
The most common are 1/4″, 3/8″ and ½” ratchet screwdrivers, but ¾” and 1″ sets are also available for heavy duty work.
How do I know the size of my sleeve?
How to determine the correct nut size for a nut
- Turn on the digital caliper and set it so that it reads in inches, not millimeters. …
- Close the yoke jaws until each jaw rests on a flat side of the nut on opposite sides.
- Check the caliper reading. …
- Turn on the digital caliper and set it to read in millimeters, not inches.
What are the key sizes in order?
American standard wrench sizes, from largest to smallest and measured in inches, are 5/8, 19/32, 9/16, 1/2, 7/16, 3/8, 11/32, 5/16, 9/32, 1 /4, 7/32, 3/16, 5/32 and 1/8. Keys are available in-game or individually. A small set consists of six to ten keys ranging in size from 5/16 to 1 inch.
Is a 3/8 jack the same as a 10mm jack?
The imperial equivalent size of a 10mm socket is a 3/8 socket.
What is the 3/16 size in MM?
Inch to mm conversion table
< td > 3/16″
| Dimensions – Inch to metric | ||
|---|---|---|
| 0.188” | 4.78mm | |
| 0.250″ | 1/4″ | 6.35mm |
| 0.313″ | 5/16″ | 7.95mm |
| 0.375″ | 3/8″ | 9.53mm |
Are 6 or 12 point sockets better?
Answer: It’s true that 12-point sockets are fine for most light repairs, but heavy-duty work calls for a hex socket. A hex socket is much less likely to slip off a stubborn fastener or rounded corners. Here’s why: (1) Hex sockets have thicker walls, so they’re less likely to fly.
What are SAE key sizes?
Standard open-end wrenches (1/4, 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1) Metric Combination Wrenches (6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19) Standard Flare Nut Wrenches (3/8, 7 /16, 1 /2, 9/16, 5/8, 11/16, 3/4, 7/8) Note: Each key can combine two sizes.